Industrial Waste Removal

Guide · Businesses · 3 min read · Updated 16 November 2026

EWC Codes Explained: How to Describe Industrial Waste Correctly

Short answer

EWC codes, also called List of Waste codes, are six-digit codes used on waste transfer notes and consignment notes to describe waste. The first two digits show the source, such as an industry or process. Some wastes have mirror entries, one hazardous and one non-hazardous, so the waste must be assessed. Using the right code is part of your duty of care and decides how the waste can be handled.

A large industrial facility

What EWC codes are

The European Waste Catalogue, now referred to in UK law as the List of Waste, is a list of waste descriptions, each with a six-digit code. The codes are used across the UK on waste transfer notes for non-hazardous waste and on consignment notes for hazardous waste. They tell everyone handling the waste what it is, where it came from and whether it is hazardous.

The code is split into three pairs of digits. The first pair identifies the chapter, usually the industry or process that produced the waste. The second pair identifies a sub-chapter. The last pair identifies the specific waste.

Examples from industrial sites

These are common examples only. The correct code depends on how your waste was produced and what it contains, so always check the full guidance or ask your waste contractor.

WasteExample codeNotes
Mixed packaging15 01 06Non-hazardous mixed packaging
Wooden packaging and pallets15 01 03Non-hazardous
Waste mineral engine oil13 02 05*Hazardous, marked with an asterisk
Iron and steel scrap17 04 05From construction and demolition
Oily rags and absorbents15 02 02*Hazardous if contaminated by hazardous substances
Mixed municipal-type waste20 03 01General waste from offices and canteens

Hazardous waste and mirror entries

Codes marked with an asterisk are hazardous waste. Some wastes are always hazardous, such as waste mineral oils. Others are covered by mirror entries: two codes for the same type of waste, one hazardous and one non-hazardous. Which one applies depends on whether the waste contains dangerous substances above certain thresholds.

For mirror entries, the producer must assess the waste, using information such as safety data sheets, knowledge of the process and, where needed, sampling and analysis. The Environment Agency's technical guidance on waste classification, often called WM3, sets out how to do this across the UK.

  • Identify the process or activity that produced the waste.
  • Find the chapter that matches the source.
  • Check whether the waste has an absolute hazardous code or a mirror entry.
  • For mirror entries, assess the substances present using safety data sheets or testing.
  • Record the code and the assessment, and share it with your waste contractor.

Why the code matters

The code decides which waste sites can legally accept the waste, how it must be transported and what paperwork is needed. If waste is wrongly described, it may end up at a site that is not permitted to take it, which can lead to enforcement action against both the producer and the carrier. Hazardous waste described as non-hazardous is a particularly serious problem.

Your duty of care requires an accurate written description of the waste whenever it is transferred. The EWC code is a key part of that description, alongside a written explanation of what the waste is and how it arose.

Common mistakes when coding waste

One frequent mistake is choosing a code from the wrong chapter. Waste should first be coded from the chapter that matches the activity that produced it, such as metalworking or vehicle maintenance, before falling back to more general chapters. Another is using a general mixed waste code for loads that should be separated, which can mean recyclable or hazardous materials are handled incorrectly.

A third common problem is assuming waste is non-hazardous because it looks harmless. Absorbents used to clean up oil, empty containers that held hazardous substances and fluorescent tubes can all be hazardous. Packaging contaminated with residues of dangerous substances has its own hazardous code.

Finally, codes are sometimes copied from old paperwork without checking whether the process or materials have changed. Review your waste descriptions when you change suppliers, products or processes, and at least once a year. A short waste audit with your contractor often finds savings as well as compliance issues.

Waste transfer notes and consignment notes

Non-hazardous waste transfers in England and Wales need a waste transfer note, which records the code, a description, the quantity, the parties involved and the date. Regular collections of the same waste can be covered by a season ticket note for up to a year. Hazardous waste needs a consignment note for each movement in England and Wales, with similar systems in Scotland and Northern Ireland. Keep transfer notes for at least two years and hazardous waste records for at least three years.

Getting help

A reputable industrial waste contractor will help you identify the right codes, assess mirror entries and complete the paperwork. Provide safety data sheets and details of your processes when asking for a quote. Guide prices include van loads of mixed industrial waste at £180–£350, 205-litre drums of waste oil or coolant at £60–£150 and IBCs of liquid waste from £150.

Many contractors will carry out a site waste review, listing each waste stream with its code, container and collection frequency. Keeping this list up to date makes audits, inspections and staff training much easier.

Questions people also ask

What does the asterisk on an EWC code mean?

An asterisk marks a hazardous waste code. Waste with an asterisked code must be handled as hazardous waste, with consignment notes and suitable carriers and sites.

Who decides the EWC code for waste?

The waste producer is responsible for describing and classifying their waste, including choosing the code. Waste contractors can help, but the legal duty sits with the producer.

What is a mirror entry?

A mirror entry is a pair of codes for the same type of waste, one hazardous and one non-hazardous. The producer must assess the waste to decide which applies, usually from safety data sheets or analysis.

Written and checked by the Industrial Waste Removal team. Read our editorial policy.

Get a free industrial waste removal quote

Tell us what you need and we'll come back with a clear price.

Request a quote