Guide · Businesses · 4 min read · Updated 16 November 2026
Industrial Machinery Removal: Decommissioning and Disposal
Short answer
Removing industrial machinery involves isolating power, compressed air and other services, draining oils and coolants, dismantling or cutting where needed, then lifting and transporting the equipment safely. Machines with resale value can be sold; others are stripped for scrap metal recycling. Fluids are collected as hazardous waste with consignment notes. Machinery removal typically starts from £300, and scrap or resale value may reduce the cost.
Planning a machinery removal
Every machine removal starts with a plan. That means knowing what the machine is, how much it weighs, how it is fixed to the floor, what services feed it and what fluids it contains. It also means checking the route out: door sizes, floor loadings, overhead obstructions and where a vehicle can be loaded. A method statement and risk assessment should set out how the machine will be isolated, drained, dismantled, lifted and moved, and who is responsible for each step. For large or complex equipment, a lift plan prepared by a competent person is needed. Gather the machine's manual if you still have it. It often shows lifting points, weights and fluid capacities, which make planning easier and safer.
- Make, model, weight and dimensions
- Fixings, such as floor bolts, grouting or anti-vibration mounts
- Services: electricity, compressed air, water, gas, extraction
- Fluids: hydraulic oil, lubricants, coolants and fuel
- Route out, floor loading and loading point
Isolation and draining
Machines must be fully isolated before work begins. Electrical supplies should be isolated and disconnected by a competent electrician, compressed air lines vented and capped, and water and gas supplies isolated and made safe by qualified people. Stored energy in springs, accumulators and raised parts needs releasing safely. Fluids are drained into suitable containers. Hydraulic oil, lubricants and coolants are usually hazardous waste and must be collected with a consignment note under the Hazardous Waste Regulations 2005 in England and Wales, or the special waste rules in Scotland. Draining before moving prevents leaks during lifting and transport. Lock-out and tag-out procedures help here. Each isolation point is locked and tagged so nobody can re-energise the machine while people are working on it, and the locks are only removed once the work is complete or the services have been permanently disconnected.
Moving the machine
Once isolated and drained, the machine is released from its fixings. Depending on size and weight, it may be moved whole using machine skates, jacks, forklifts or a crane, or dismantled into sections. Where resale is not an option, cutting large frames on site can make removal simpler, though hot cutting needs fire precautions and a permit system on most sites. Lifting operations should follow a lift plan, with lifting equipment inspected and operators trained. The aim is to move heavy equipment under control, without damaging the building or the floor. Protect the building as the machine moves. Floor plates spread the load over weaker surfaces, and door frames, columns and racking along the route should be protected or removed temporarily.
| Method | Typical use |
|---|---|
| Machine skates and jacks | Heavy machines moved across floors to a loading point |
| Forklift | Medium machines with suitable lifting points |
| Mobile or lorry-mounted crane | Very heavy items or lifts out through roofs or over obstacles |
| Dismantling | Machines too large for doors or with resale value in parts |
| On-site cutting | Scrap machines too large to move whole |
Resale, scrap and recycling
Before scrapping a machine, consider whether it has resale value. Working machines from known manufacturers, with documentation, can often be sold to dealers or other businesses. Where resale is not realistic, machines are stripped for scrap. Steel, cast iron, copper windings in motors, aluminium and brass all have value, which reduces the overall cost of removal. Under the Scrap Metal Dealers Act 2013, scrap metal dealers in England and Wales must hold a local authority licence and cannot pay for scrap in cash. Electrical components and control panels may be electrical waste under the WEEE Regulations 2013. Ancillary equipment adds value too. Electric motors, gearboxes, pumps and control gear can often be sold separately, even when the main machine is scrapped. Ask your contractor to separate these items where it makes sense.
Paperwork to keep
Keep records of what was removed and where it went. That includes consignment notes for hazardous fluids, kept for three years in England and Wales, waste transfer notes for non-hazardous waste, kept for at least two years, and receipts for scrap metal or asset sales. If the machine was listed on an asset register, update it. Where machines contained data, such as CNC controllers storing programs, decide whether that data needs wiping or the storage destroying. Keep a note of the machine's serial number alongside the paperwork, so its disposal can be matched to your asset register and insurance records.
Common pitfalls
Underestimating weight is the most common problem. Industrial machines are often much heavier than they look, particularly those with cast iron bases. Floor loadings and route capacity must be checked, especially on upper floors and mezzanines. Hidden fluids are another issue: sumps, gearboxes and hydraulic reservoirs that were not drained can leak during lifting. Finally, services must be properly isolated and capped, not simply switched off, so the area is safe once the machine has gone. Rushing is the other common pitfall. Leaving machinery removal until the final days of a lease or a factory refit often means expensive weekend working, limited crane availability and no time to find buyers for equipment with resale value. Early planning almost always reduces the total cost.
Questions people also ask
Who disconnects the electrics on industrial machinery?
Electrical isolation and disconnection should be carried out by a competent electrician, who will make the supply safe and terminate or remove cables properly. Compressed air, water and gas supplies also need isolating and capping by suitably qualified people before the machine is moved.
Can old machinery be sold instead of scrapped?
Often, yes. Working machines from established manufacturers, especially with manuals and service records, can have resale value to dealers or other businesses. Even non-working machines may be bought for parts such as motors and gearboxes. Resale value can reduce or offset the cost of removal.
What happens to the oil in old machinery?
Hydraulic oils, lubricants and coolants are drained before the machine is moved. They are usually hazardous waste, so they are collected in suitable containers with a consignment note and sent for treatment, such as re-refining or recovery, at a permitted facility.
Written and checked by the Industrial Waste Removal team. Read our editorial policy.
More guides
How Much Does Industrial Waste Removal Cost in the UK?
In the UK, a van load of mixed industrial waste typically costs £180–£350 to remove. A 20 to 40 yard roll-on roll-off container costs £350–£900, a…
Hazardous Waste Consignment Notes: A Guide for Businesses
In England and Wales, the Hazardous Waste Regulations 2005 require hazardous waste to be moved with a consignment note that records the waste, its…
Business Waste Duty of Care: What Industrial Sites Must Do
Under section 34 of the Environmental Protection Act 1990, every business must store waste safely, describe it accurately, hand it only to authorised…
Factory and Warehouse Clearance: A Planning Checklist
Plan a factory or warehouse clearance by listing everything that must go, identifying hazardous items and machinery, and arranging a survey. Agree a…
EWC Codes Explained: How to Describe Industrial Waste Correctly
EWC codes, also called List of Waste codes, are six-digit codes used on waste transfer notes and consignment notes to describe waste. The first two…
Waste Oil and Coolant Disposal for Workshops and Factories
Waste oils, cutting fluids and coolants from workshops and factories are usually hazardous waste. Store them in sound, labelled containers with…
Get a free industrial waste removal quote
Tell us what you need and we'll come back with a clear price.
Request a quote